Skip to Content
Server Products Commerical Food Service Equipment
Main Content

Cold Station | (2) Jars & Solution™ Pumps

Model:SB-2P/N:79790GTIN:687329007622List:$650.50 USD
Wish List How To Buy
  • Bar Combo (2) Solution Pumps
  • Alt Image A

This insulated bar combo includes two Solution™ pumps and deep plastic fountain jars. The brushed finish base reduces the visibility of fingerprints and may be cooled with (2) Universal Ice Packs 100515, HoldCold Jars or ice. Ice packs and HoldCold jars are sold separately.

Polycarbonate Solution™ pumps are quite versatile in their ability to dispense a variety of thick, thin and even products with particulates. Unlike most plastic pumps, Solution™ pumps offer adjustable portion control, can be disassembled, are dishwasher safe and NSF listed. A 1 ounce (30 mL) serving is the maximum portion per stroke. Portions can be reduced in 1/4 ounce (7 mL) increments, using the supplied gauging collars.

Key Benefits Inlcude:
  • Brushed finish base reduces the visibility of fingerprints
  • Insulation eliminates condensation on outside, when chilling
  • (2) Polycarbonate Solution™ pumps; parts are removable & dishwasher safe
  • 1 oz (30 mL) maximum portion, adjusts in 1/4 oz (7 mL) increments
  • Dispense a wide range of cold products from syrups to pumpable relish by selecting (1) of the (3) discharge fittings included
  • (2) Deep, white plastic fountain jars
Dispenses:
Thin
Thick
Thicker
Certifications:
2YrWarranty
NSF
Warning-Prop65
Serving Application:
Ambient
Cold
  • Specifications
  • Documentation
  • Trouble Shooting
GTIN687329007622
Dimensional Weight28 lb | 12.7 kg
International Dim Wt34 lb | 15.4 kg

Specification Sheet

  • Fountain Jars, Standard and Slim Sized | Specs 02158
    Fountain Jar Cold Stations | Specs 02020

    Specs for cold stations with stainless steel or Solution pumps or lid and ladle stations. Each include insulated stainless steel base, fountain jars and pumps or hinged lids and ladles.

Manuals

Problem:

Why is my Solution pump dripping product?

Solution:

Solution pumps come with (3) discharge fittings with varying opening sizes. Thick products work with the largest opening and thin the smallest. If your product is dripping, it may need the next smaller opening from what is installed. Too hard to push? Use the discharge fitting with a larger opening.

Problem:

Why is my Solution  pump difficult to push down to pump?

Solution:

Solution pumps come with (3) discharge fittings with varying opening sizes. Thick products work with the largest opening and thin the smallest. If it's too hard to push, you may need the discharge fitting with the next larger opening.

Problem:

Why does my Solution pump dispense only a little or no product?

Solution:

When this happens on a Solution pump, the first place to look is within the pump assembly. With the pump apart, check if the ball valves and seal are properly installed. Ball valves must be facing downward.

Our trick to remembering this is to say, in your mom's voice, "Put the BALL DOWN!". My bet is you won't forget it, no matter how hard you try.

Problem:

Why isn't my Solution pump returning to the start position after dispensing?

Solution:

If the plunger is not returning to start position after dispensing, it may likely be a broken spring. The spring is a replacement piece that will eventually wear out and break.

Sometimes how the pump is assembled can cause it to "lock-up" somewhat. During assembly, compress the pump and spring, while aligning flats on piston with the flats inside the cylinder. Another tip is the locking collar should be installed with the pump compressed.

Recommended Items

* Server Products equipment is sold through dealers or distributors. The list prices shown throughout the site are for estimating cost.
The final cost may be lower or higher based on your location, taking into account taxes, landing fees, etc.