Need help? Use our Equipment Finder to choose the proper product for your application.

Express (3) Pouch Dispensing Station

Model:SE-3P/N:07040List:$886.00 USD
  • Server Express Rail (3) Pouched Product Pumps

The Server Express™ Triple system dispenses from (3) 1½ gallon (or 6 L) pouches with 16 mm fitments. It features surgical-quality plastic pumps that are quick to break down, dishwasher safe and achieve up to 98% evacuation. The stainless steel shroud with lid is designed for countertop use.

The Express™ pump has a special connector that pierces the pouch fitment creating a sealed system for maximum evacuation and savings. A full portion yields 1 oz (30 mL) which can be reduced in ¼ oz (7 mL) increments simply by adjusting the portion pin position on the lid lever.

Standard features include:

  • Stainless steel shroud and lid Works with 1½ gallon (or 6 L) pouch, 16 mm fitment
  • Pump is constructed of surgical-quality plastic parts
  • Quick to breakdown and dishwasher safe
  • Pump is ADA compliant (requiring less than 5 lbs of pressure to dispense)
  • 1 oz (30 mL) maximum portion, adjusts in ¼ oz (7 mL) increments
  • NSF Listed
  • 2-Year Warranty
Serving Application:
  • 2-Year Warranty
  • Crafted In the USA
  • Specifications
  • Documentation
  • Videos
  • Trouble Shooting
Height17 1/2"
Width16 3/8"
Depth13 5/16"
Weight18 lb
Works With1.5 gal, 18 mm fitment pouch
Capacity(3) 1.5 gal
Dispense Typelever pump
Full Portion1 oz
Portionadjustable in 1/4 oz increments; up to 1 oz
NSF ListedY
ADA CompliantY



  • Express Manual
    Express Dispensers | Manual 01534-P

    Manual for Express | Various Models | Includes: Safety, Drop-In Units, Pump Model, Pump Assembly, Setup, Portion Control, Disassembly, Cleaning, Stainless Steel Care, Troubleshooting

Parts Breakdown

CAD Drawings


Why is my Solution pump dripping product?


Solution pumps come with (3) disharge fittings with varying opening sizes. Thick products work with the largest opening and thin the smallest. If your product is dripping, it may need the next smaller opening from what is installed. Too hard to push? Use the discharge fitting with a larger opening.


Why is my Solution  pump difficult to push down to pump?


Solution pumps come with (3) disharge fittings with varying opening sizes. Thick products work with the largest opening and thin the smallest. If it's too hard to push, you may need the discharge fitting with the next larger opening.


Why does my Solution pump dispense only a little or no product?


When this happens on a Solution pump, the first place to look is within the pump assembly. With the pump appart, check if the ball balves and seal are properly installed. Ball valves must be facing downward.

Our trick to remembering this is to say, in your mom's voice, "Put the BALL DOWN!". My bet is you won't forget it, no matter how hard you try.


Why isn't my Solution pump returning to the start position after dispensing?


If the plunger is not returning to start position after dispensing, it may likely be a broken spring. The spring is a replacment piece that will eventually wear out and break.

Sometimes how the pump is assembled can cause it to "lock-up" somewhat. During assembly, compress the pump and spring, while aligning flats on piston with the flats insde the cylinder. Another tip is the locking collar should be installed with the pump compressed.

Recent and Recommendations

Recommended Items

    * Server Products equipment is sold through dealers or distributors. The list prices shown throughout the site are for estimating cost. The final cost may be lower or higher based on your location, taking into account taxes, landing fees, etc.