Skip to Content
 
Server Products Commerical Food Service Equipment
Main Content

Slim Jar Fountainette Pumps - Stainless Steel

Model:FP Slim Fountainette
View Options How To Buy
  • Slim Jar Fountainette Pumps - Stainless Steel

Add additional syrups and flavors to your existing fountainette with slim fountain jar pumps. These pumps use a narrower lid to fit slim fountain jars and operate at a 22º angle for additional flavors in the same footprint. Models for 1 1/2 qt (1.4 L) and 2 qt (1.9 L) slim fountain jars with standard or taller discharge point for additional clearance.

Stainless steel pumps are constructed with a cast valve body featuring captured balls to prevent loss, have exacting portion control and will last for years with routine maintenance. Pumps are adjustable in 1/8 oz (3.7 mL) increments. To retrofit, order a slim fountain jar and lid only for your full-size fountain jar pump.

The slim fountain jar is available exclusivly from Server Products.

Dispenses:
Thin
Certifications:
2YrWarranty
BPA-Free
NSF
Serving Application:
Ambient
Cold
  • Variations
  • Documentation
  • Videos
  • Trouble Shooting
 DescriptionModelp/nContainer TypeCapacityServing ApplicationList Price 
FP-200 SlimSlim 1 1/2 Qt Fountain Jar, Fountainette Pump | Stainless SteelFP-200 Slim85350Fountain Jar, Slim1 1/2-quart
Ambient
Cold
$305.18 USD More Info Wish List

Brochures

Problem:

How do I stop this pump from dripping?

Solution:

To take care of this mess maker, check the seals and o-rings. If they look worn with tiny cracks or are misshapen, it's a good time for replacement.

Problem:

Why is my pump hard to push down for dispensing?

Solution:

This type of symptom was typically seen in Brazed Style (valve bodies) pumps manufactured prior to 1993. Well done on your pump maintenance, if yours is of that age. Our advice is to make sure the ball is resting on the inner valve assembly inside the cage. If that is correctly placed, also ensure the inner valve handle is on the catch.

Problem:

Why does my pump dispense only a little or no product (under dispense)?

Solution:

The next time your pump is apart for cleaning, check all seals and o-rings for wear or damage. Over time they develop tiny cracks and need to be replaced. Further investigation depends on what style (age) your pump is…

For a Cast Valve with Captured Balls (1999 to present)
Make sure the balls move freely when cleaning.

A Cast Valve with Loose Balls (1993 - 1999)
Make sure the balls are in the proper place; one in the inlet port of the valve body and the other in the discharge port.

For Brazed Valve Bodies (prior to 1993)
Make sure a ball is installed beneath the ball-retaining pin, the retaining pin is in place and a ball is resting on the inner valve assembly under the cage.

Problem:

Why is product oozing out around or under the locking collar?

Solution:

First make sure that the seal is firmly installed on the piston and stem assembly, with the flare side of the seal facing down. If the seal was installed properly, it likely needs replacing.

Problem:

Why isn't my pump returning to the top after dispensing?

Solution:

Known to insiders as a plunger problem, it's typically either a missing washer or a broken/missing spring.

The washer is necessary to compress the spring, so if it's missing, your plunger will not return. A well-used spring can become worn out or broken. The spring is also necessary for pump operation. Now you can call yourself an insider too.

Your pump Model and Part number are stamped on the lid. With that information, a parts breakdown will determine replacement part numbers.

Recommended Items

    * Server Products equipment is sold through dealers or distributors. The list prices shown throughout the site are for estimating cost.
    The final cost may be lower or higher based on your location, taking into account taxes, landing fees, etc.